Panier0Panier
Chercher
Menu
  • Qualité et style dans les sports nautiques depuis 1974
  • Livraison gratuite à partir de €100,-
  • Livraison en 2-3 jours
  • Commandé avant 12:00 les jours ouvrables, expédié le jour même
REJOIGNEZ LA FAMILLE JOBE
... et soyez le premier à lire des blogs intéressants sur les sports nautiques et des nouvelles de Jobe.
Retour à l'aperçu

How to: Replacing a Halkey Roberts valve

23 octobre 2019
Halkey Roberts boat valves are made in two parts: the nut on the inside of the SUP board and the valve itself that screws into the nut from the outside of the board. Tightening the two parts together creates an airtight seal that can easily hold 20 PSI of pressure. Replacing a valve is a pretty straight forward procedure and will approximately take 2 minutes. In the following 4 steps we will tell you exactly what to do when you want to replace the Halkey Roberts valve on your SUP board.

Step 1: The tools

The first step is to gather the right tools for the job. Do not use any tools that are not designed for removing a Halkey Roberts Valve! This can permanently damage your board! You will need the grey tool that comes with your SUP board. You can find it in the orange repair kit container. In case you do not have the repair kit, you can simply buy a new one at our webshop.

Step 2: Removing the valve 
Grab the grey tool from the orange container and press it firmly on the Valve. Start unscrewing the valve counterclockwise until it is loose enough.
When the valve is loose enough you can just use your hands to unscrew the final part and take out the valve.

How to: Replacing a Halkey Roberts valve

Step 3: Fitting the new valve
Make sure the area around the hole is clean and undamaged. If there are strings coming out the hole you grab some scissors and cut them off. Keep in mind that any dirt or strings getting stuck between the valve and the nut will damage the airtight seal permanently. Check if the Halkey Roberts valve that you are going to screw back into place is completely clean and undamaged. Center the nut inside the hole and place back your new valve on the nut. Screw it back on the inner part while holding the bottom of your sup board to support nut and valve.

How to: Replacing a Halkey Roberts valve 
 
Step 4: Checking your valve
Now that the valve is back in place tighten it up firmly still using the tool. Remove the tool from the valve and pump up your sup board to 18-20psi. Leave your board inflated and wait approximately 4 hours before checking if your board has lost any air. Is your board still on the same pressure? Congratulations, you successfully replaced your Halkey Roberts valve and you are ready to get back on the water!

Watch the movie below for a video instruction!
 
Recois Code Panier
Mettez à jour vos préférences
:
:
Veuillez choisir une taille
Je visite le Jobe Expo en ligne en tant que
Vos préférences en matière de cookies

Jobesports.com utilise des cookies pour une utilisation optimale du site Web et à des fins de médias sociaux et de publicité. Les cookies tiers sont utilisés pour les fonctionnalités des réseaux sociaux et les publicités personnalisées. Pour plus d'informations, veuillez lire notre Politique de confidentialité et de cookies. Acceptez-vous ce cookie et le traitement associé de vos données personnelles ?

Plus d'infos
Vous pouvez à tout moment modifier vos préférences en vous rendant dans la section « Paramètres des cookies » en bas de page. Consultez notre « Politique de confidentialité et de gestion des cookies » pour obtenir davantage d'informations.
Vos préférences en matière de cookies
Vous pouvez à tout moment modifier vos préférences en vous rendant dans la section « Paramètres des cookies » en bas de page. Consultez notre « Politique de confidentialité et de gestion des cookies » pour obtenir davantage d'informations.